Flow Lab

Syllabus / Module 12: Applications: Flight & Aerospace

Lesson 12.1

Airfoils, Circulation & Lift

Joukowski transformation, the Kutta condition, Kutta–Joukowski theorem, lift coefficient and angle of attack.

Written byClaude Opus

🌊
Why this matters for simulation: The theory behind your future airframe simulator.

By the end of this lesson you can…

  • Explain what a conformal map does to a flow, and why solving flow past a circle and mapping it gives flow past an airfoil.
  • Build symmetric and cambered Joukowski airfoils from an offset circle with $z = \zeta + b^2/\zeta$, and explain why the trailing edge is a cusp.
  • Derive the Kutta circulation $\Gamma = 4\pi U a\sin(\alpha + \beta)$ from the trailing-edge stagnation point, and explain physically why the flow chooses it.
  • Compute $C_L = 8\pi a\sin(\alpha + \beta)/c \approx 2\pi(1 + \varepsilon)\sin(\alpha + \beta)$, its flat-plate and small-angle forms, the zero-lift angle, and check the $2\pi$ slope numerically.
  • Read a $C_p$ distribution, connect the leading-edge suction peak to the adverse gradient that stalls a real wing, and close the light-aircraft lift budget at $12\,633$ N.
On this page
·
  1. Airfoil vocabulary
  2. Conformal maps: potential flow’s superpower
  3. The Joukowski map
  4. Flow past the tilted circle
  5. The Kutta condition
  6. Lift and the lift curve
  7. Worked example: the light aircraft, closed
  8. The pressure on the skin
  9. Ideal and real lift curves: stall
  10. Computing it
  11. Concept checks
  12. Problems
  13. Key Takeaways

Module 11 ended on a promise: a wing makes lift L=ρVΓL = \rho V\Gamma per metre of span, the Kutta condition decides how much circulation the sharp trailing edge allows, and the starting vortex of 11.6 Vorticity Dynamics & Circulation balances it. For the light aircraft (chord 1.51.5 m, 5050 m/s, CL=0.5C_L = 0.5) that bound circulation was 18.7518.75 m2^2/s, lifting 12 63312\,633 N over an 1111 m span. But 11.7 Potential Flow & Stream Functions‘s lifting cylinder was a streamline for every Γ\Gamma: theory alone could not say how much lift there is. A real wing does say. Here one formula turns that cylinder into wing shapes, the shape picks its circulation, and lift, the lift curve and the skin pressure follow, up to where the ideal answer fails: stall.

Tools: 11.7 Potential Flow & Stream Functions (complex potential, dw/dz=u−ivdw/dz = u - iv), 11.6 Vorticity Dynamics & Circulation (Kelvin, the starting vortex), 11.8 Boundary Layers (separation), 11.3 Momentum: Pressure & the Euler Equations (Bernoulli) and 2.9 Line Integrals, Circulation & Flux (circulation as a line integral).

▶ Video A circle mapped by z = zeta + b^2/zeta into a flat plate, a teardrop and a cambered airfoil; the streamlines carried along; the circulation sliding the rear stagnation point onto the cusp; and the suction peak that grows until a real wing stallscaptions only
Transcript
  1. Module 11 left a promise. A wing makes lift, rho V gamma per metre of span, and the starting vortex it sheds is the price. Our light aircraft needed a circulation of 18.75, lifting 12 633 newtons over an 11 metre span. But a cylinder is a streamline for every circulation. So what sets gamma? The answer starts with a map.
  2. Solve the flow past a circle once, then move the circle with a conformal map. Locally it only scales and rotates, so streamlines stay streamlines and circulation is carried along. Joukowski's map is z equals zeta plus b squared over zeta. Shift the circle left by epsilon, 0.10, and the front swells into a teardrop. Lift it by kappa, 0.04, and the plate bends into a cambered airfoil, beta 2.0826 degrees. At zeta equals b the map squares the distance, doubling the angle: 180 degrees become 360, a cusp.
  3. With zero circulation at 4 degrees, air from the lower surface must whip round the sharp edge: 0.45 micrometres from the cusp the speed is 4768 metres per second, and the rear stagnation point sits 5.03 millimetres ahead of the edge. Real air will not do that. The boundary layer separates and sheds the starting vortex, leaving circulation on the wing, until the flow leaves smoothly. Then the speed is a finite 45.17.
  4. Put the stagnation point on the trailing edge and the circle gives gamma equals 4 pi U a sine of alpha plus beta. At 4 degrees that is 27.254 square metres per second, a lift coefficient of 0.7268. Watch the circulation grow from zero: the streamlines bend, and the rear stagnation point slides back until it sits exactly on the cusp.
  5. Now close the aircraft's story: chord 1.5 metres, 50 metres per second, lift coefficient 0.5. A flat plate needs 4.5643 degrees. Our cambered design needs only 2.0979: camber saves two degrees, thickness the rest. Either way the circulation is 18.75, because lift coefficient, speed and chord fix it. Lift per metre is 1.225 times 50 times 18.75, which is 1148.4375 newtons, and over 11 metres, 12 633 newtons.
  6. The lift curve is a sine. For the flat plate the slope is exactly 1.000000 times 2 pi; the thick design's is 1.090897 times 2 pi, because thickness raises the ideal slope. Camber slides the whole curve up: lift is zero not at zero degrees but at alpha minus beta, minus 2.0826 degrees.
  7. Lift is the area between the pressure curves. Plot minus Cp on the upper surface. The suction peak deepens far faster than the lift, and slides onto the nose: minus 0.599 at zero degrees, minus 1.505 at 4, minus 3.885 at 8, minus 7.863 at 12, and minus 11.846 at 15. The stagnation point slides under the nose.
  8. Behind the peak the air must slow again. At 15 degrees the pressure climbs from minus 11.8 to plus 0.25 within 1.5 metres: an adverse gradient. The boundary layer, slowed by no-slip, eventually separates, the Kutta condition fails, circulation falls, and the wing stalls. Typical sections stall near 15 degrees with lift coefficients 1.4 to 1.6, from memory, while the ideal curve keeps rising to 2.0148.
  9. Honest limits. Joukowski profiles are not real airfoils: the cusp is too thin to build. This is two-dimensional, while real wings have tip vortices. It is inviscid, so no drag and no stall. And it is incompressible, fine at Mach 0.15. Next, 12.2: general shapes have no neat map, so we replace the airfoil by a sheet of vortices, demand a streamline at every panel plus Kutta, and solve a linear system.

Airfoil vocabulary

An airfoil is a wing’s cross-section: sharp trailing edge at the back, rounded leading edge in front, the chord cc (1.51.5 m) joining them. The camber line runs midway between the surfaces; its greatest height is the camber, the greatest gap the thickness t/ct/c, both as fractions of cc. The angle of attack α\alpha is between chord and oncoming air; lift per span L′L' is perpendicular to that air, and CL=L′/(12ρU2c)C_L = L'/(\tfrac12\rho U^2 c).

Conformal maps: potential flow’s superpower

In 11.7 every formula w(z)w(z) in one complex variable was a potential flow, with dw/dz=u−ivdw/dz = u - iv. Now chain two formulas. Know the flow w(ζ)w(\zeta) past a circle in a “circle plane” ζ\zeta, and take a formula z=Z(ζ)z = Z(\zeta) that moves every point somewhere else. Then ww, written through zz, is still a formula in one complex variable: still a potential flow, now in the zz plane.

What does the map do to a picture? Near a point ζ1\zeta_1, Taylor gives Z(ζ1+δ)≈Z(ζ1)+Z′(ζ1) δZ(\zeta_1 + \delta) \approx Z(\zeta_1) + Z'(\zeta_1)\,\delta, and multiplying by the complex number Z′(ζ1)=reiφZ'(\zeta_1) = re^{i\varphi} scales by rr and rotates by φ\varphi (11.7). So locally the map only scales and rotates, equally in every direction: tiny squares stay tiny squares, right angles stay right. That is conformal. Each streamline goes to a curve with the same ψ\psi, so the body stays a solid wall. Three more facts:

  • If Z(ζ)≈ζZ(\zeta) \approx \zeta far away, the free stream is untouched: speed UU at angle α\alpha in both planes.
  • Circulation is the jump of ϕ\phi once round the body, and ϕ\phi is just carried along by the map, so the circulation is the same in both planes. So is the lift, ρUΓ\rho U\Gamma, since by Blasius (11.7) it depends only on the far field.
  • Velocities follow the chain rule: dwdz=dw/dζdz/dζ\dfrac{dw}{dz} = \dfrac{dw/d\zeta}{dz/d\zeta}. Where dz/dζ=0dz/d\zeta = 0 the map is not conformal, and the division warns of trouble.

Strategy: solve the circle once, by hand, then map it to the shape you want.

The Joukowski map

The map is

z=ζ+b2ζ,z = \zeta + \frac{b^2}{\zeta},

with bb a constant (often written cc; here cc is the chord). Far away z≈ζz \approx \zeta. Its derivative dz/dζ=1−b2/ζ2dz/d\zeta = 1 - b^2/\zeta^2 vanishes at the two critical points ζ=±b\zeta = \pm b. You met it in 11.7’s callout: the circle ζ=beiθ\zeta = be^{i\theta} goes to z=2bcos⁡θz = 2b\cos\theta, a flat plate of chord 4b4b, with ζ=±b\zeta = \pm b landing on its two edges.

Now move the circle but keep it passing through ζ=b\zeta = b. Put its centre at

ζ0=b(−ε+iκ),a=b(1+ε)2+κ2,β=arctan⁡κ1+ε.\zeta_0 = b(-\varepsilon + i\kappa), \qquad a = b\sqrt{(1 + \varepsilon)^2 + \kappa^2}, \qquad \beta = \arctan\frac{\kappa}{1 + \varepsilon} .

The radius aa is the distance from ζ0\zeta_0 to bb, and seen from the centre the point bb sits at angle −β-\beta: b=ζ0+ae−iβb = \zeta_0 + ae^{-i\beta}.

  • Shift left (ε>0\varepsilon \gt 0): the circle swells past −b-b, so the front fattens into a rounded nose while the back still touches bb: a symmetric teardrop. At ε=0.10\varepsilon = 0.10 the sim measures t/c=11.79%t/c = 11.79\% at x/c=0.25x/c = 0.25, and its chord is 4.0333b4.0333b (Problem 1).
  • Shift up (κ>0\kappa \gt 0): the plate bends into an arc. With ε=0\varepsilon = 0 the top of the circle, ζ=ib(κ+1+κ2)\zeta = ib(\kappa + \sqrt{1 + \kappa^2}), maps to z=2iκbz = 2i\kappa b (Problem 2), so the camber is h/c=κ/2h/c = \kappa/2.
  • Both: a cambered airfoil. Our design, ε=0.10\varepsilon = 0.10 and κ=0.04\kappa = 0.04, has t/c=11.80%t/c = 11.80\%, camber 1.82%1.82\% at mid-chord and β=2.0826∘\beta = 2.0826^\circ; scaled to a 1.51.5 m chord, b=0.371897b = 0.371897 m and a=0.409357a = 0.409357 m.

Why the tail is a cusp. Exactly, z−2b=(ζ2−2bζ+b2)/ζ=(ζ−b)2/ζz - 2b = (\zeta^2 - 2b\zeta + b^2)/\zeta = (\zeta - b)^2/\zeta. Near the critical point the map squares the distance from bb, and squaring doubles angles. The circle passes bb as a smooth curve, an angle of 180∘180^\circ; doubled, 360∘360^\circ: upper and lower surfaces meet tangent to each other, a cusp. Everywhere else the map is conformal and the circle’s smoothness survives, which is why the nose is round.

Flow past the tilted circle

In the circle plane, a stream UU at angle α\alpha past a circle of radius aa centred at ζ0\zeta_0, with clockwise circulation Γ\Gamma (positive means lift up, as in 11.7):

w(ζ)=U[(ζ−ζ0)e−iα+a2eiαζ−ζ0]+iΓ2πlog⁡(ζ−ζ0).w(\zeta) = U\Big[(\zeta - \zeta_0)e^{-i\alpha} + \frac{a^2e^{i\alpha}}{\zeta - \zeta_0}\Big] + \frac{i\Gamma}{2\pi}\log(\zeta - \zeta_0) .

It is 11.7’s cylinder with the stream turned by α\alpha (the factor e−iαe^{-i\alpha} rotates the picture) and moved to ζ0\zeta_0. Differentiate:

dwdζ=U[e−iα−a2eiα(ζ−ζ0)2]+iΓ2π(ζ−ζ0).\frac{dw}{d\zeta} = U\Big[e^{-i\alpha} - \frac{a^2e^{i\alpha}}{(\zeta - \zeta_0)^2}\Big] + \frac{i\Gamma}{2\pi(\zeta - \zeta_0)} .

On the circle, ζ−ζ0=aeiθ\zeta - \zeta_0 = ae^{i\theta}. Substitute and multiply by eiθe^{i\theta}:

eiθdwdζ=U[ei(θ−α)−e−i(θ−α)]+iΓ2πa=i[2Usin⁡(θ−α)+Γ2πa],e^{i\theta}\frac{dw}{d\zeta} = U\big[e^{i(\theta - \alpha)} - e^{-i(\theta - \alpha)}\big] + \frac{i\Gamma}{2\pi a} = i\Big[2U\sin(\theta - \alpha) + \frac{\Gamma}{2\pi a}\Big],

using eiϕ−e−iϕ=2isin⁡ϕe^{i\phi} - e^{-i\phi} = 2i\sin\phi. The result is purely imaginary, so the velocity is purely tangential: the circle is a streamline, for every Γ\Gamma. The surface speed is ∣2Usin⁡(θ−α)+Γ/(2πa)∣\big|2U\sin(\theta - \alpha) + \Gamma/(2\pi a)\big|, zero at two stagnation points.

The Kutta condition

On the airfoil the speed is ∣dw/dζ∣/∣dz/dζ∣|dw/d\zeta| / |dz/d\zeta|, and at the trailing edge, ζ=b\zeta = b, the denominator is zero. Unless the circle-plane velocity vanishes there too, the airfoil speed is infinite: the air whips round the cusp from the lower surface to the upper. Near the edge, with ζ−b=s\zeta - b = s, dz/dζ≈2s/bdz/d\zeta \approx 2s/b while the distance from the cusp is d≈s2/bd \approx s^2/b, so the speed grows like 1/d1/\sqrt d (Problem 3).

In the sim, untick the Kutta condition with Γ=0\Gamma = 0 at α=4∘\alpha = 4^\circ: the surface speed 0.450.45 micrometres from the cusp reads 47684768 m/s, and the rear stagnation point sits 5.035.03 mm ahead of the edge on the upper surface, so the lower-surface air must turn the cusp. Real air will not do that. Past the corner the speed would have to fall from huge back to normal, an enormously adverse pressure gradient, so the boundary layer (11.8) separates right at the edge. What leaves is vorticity, rolled up: the starting vortex of 11.6, counterclockwise. By Kelvin the loop around wing plus starting vortex keeps zero circulation, so each bit shed leaves an equal clockwise circulation bound to the wing, which pushes the rear stagnation point back toward the edge. Shedding stops once the stagnation point sits on the trailing edge and the flow leaves smoothly. That end state is the

Kutta condition: the flow leaves a sharp trailing edge smoothly, with finite velocity.

Not a new law: the steady outcome of viscosity, valid while the boundary layer stays attached.

The algebra. The circle-plane velocity must vanish at the point that maps to the cusp, θ=−β\theta = -\beta:

2Usin⁡(−β−α)+Γ2πa=0  ⟹  Γ=−4πUasin⁡(−α−β)=4πUasin⁡(α+β).2U\sin(-\beta - \alpha) + \frac{\Gamma}{2\pi a} = 0 \;\Longrightarrow\; \Gamma = -4\pi Ua\sin(-\alpha - \beta) = 4\pi Ua\sin(\alpha + \beta) .

For our design at α=4∘\alpha = 4^\circ, Γ=4π⋅50⋅0.409357⋅sin⁡(6.0826∘)=27.254\Gamma = 4\pi\cdot50\cdot0.409357\cdot\sin(6.0826^\circ) = 27.254 m2^2/s, as the sim prints; with Kutta ticked the speed 0.450.45 micrometres from the cusp is 45.1745.17 m/s, finite (at a cusp it need not be zero; the flat plate’s is Ucos⁡αU\cos\alpha).

◆ Interactive Joukowski airfoil designer: circle plane and airfoil plane, streamlines and tracers, Kutta circulation, Cp on the surface and the lift curve

Loading simulation…

Both planes draw the same ψ\psi levels, so each streamline on the left is carried to one on the right.

Lift and the lift curve

Kutta–Joukowski (11.7), L′=ρUΓL' = \rho U\Gamma, survives the map. Divide by 12ρU2c\tfrac12\rho U^2c:

CL=Γ12Uc=8πacsin⁡(α+β).C_L = \frac{\Gamma}{\tfrac12 Uc} = \frac{8\pi a}{c}\sin(\alpha + \beta) .

Thin-airfoil form. For small ε\varepsilon and κ\kappa, c≈4bc \approx 4b and a≈b(1+ε)a \approx b(1 + \varepsilon), so

CL≈2π(1+ε)sin⁡(α+β)≈2π(1+ε)(α+β),α in radians.C_L \approx 2\pi(1 + \varepsilon)\sin(\alpha + \beta) \approx 2\pi(1 + \varepsilon)(\alpha + \beta), \quad \alpha \text{ in radians}.

Flat plate. With ε=κ=0\varepsilon = \kappa = 0 these are exact (a=ba = b, c=4bc = 4b, β=0\beta = 0): CL=2πsin⁡αC_L = 2\pi\sin\alpha, and for small α\alpha, CL≈2παC_L \approx 2\pi\alpha, a slope of 2π2\pi per radian (0.109660.10966 per degree). At 10∘10^\circ the two differ by half a percent (1.09111.0911 against 1.09661.0966).

Zero-lift angle. CL=0C_L = 0 at αL0=−β\alpha_{L0} = -\beta (−2.0826∘-2.0826^\circ for the design: click zero-lift alpha). For a pure arc β=arctan⁡(2h/c)≈2h/c\beta = \arctan(2h/c) \approx 2h/c; the design’s 1.82%1.82\% camber gives 2h/c=0.03642h/c = 0.0364 rad =2.086∘= 2.086^\circ, close. Thin airfoil theory (12.2) finds −2h/c-2h/c again.

The slope, numerically. At α=0\alpha = 0 the sim’s central difference reads 1.000000×2π1.000000\times2\pi for the flat plate and 1.090897×2π1.090897\times2\pi for the design. Exactly, dCL/dα=8πacos⁡β/cdC_L/d\alpha = 8\pi a\cos\beta/c there, with acos⁡β=b(1+ε)a\cos\beta = b(1 + \varepsilon): thickness raises the ideal slope by about ε\varepsilon. The exercise verifies both.

Worked example: the light aircraft, closed

Same wing: c=1.5c = 1.5 m, U=50U = 50 m/s, ρ=1.225\rho = 1.225 kg/m3^3, CL=0.5C_L = 0.5.

  1. Flat plate (11.7’s preview): sin⁡α=0.5/(2π)\sin\alpha = 0.5/(2\pi), α=4.5643∘\alpha = 4.5643^\circ.
  2. Our cambered Joukowski airfoil: sin⁡(α+β)=0.5c/(8πa)=0.072899\sin(\alpha + \beta) = 0.5c/(8\pi a) = 0.072899, so α+β=4.1805∘\alpha + \beta = 4.1805^\circ and α=2.0979∘\alpha = 2.0979^\circ. Camber (β\beta) saves two degrees, thickness (a/ba/b) the rest.
  3. Circulation: Γ=4π⋅50⋅0.409357⋅0.072899=18.75\Gamma = 4\pi\cdot50\cdot0.409357\cdot0.072899 = 18.75 m2^2/s, 11.6’s number: CLC_L, UU and cc fix Γ=12UcCL\Gamma = \tfrac12UcC_L whatever the shape.
  4. Lift: L′=1.225⋅50⋅18.75=1148.4375L' = 1.225\cdot50\cdot18.75 = 1148.4375 N/m; over 1111 m, as a 2D strip, 12 632.812\,632.8 N, the 12 63312\,633 N of 11.6. The story closes.

The lab also sums the surface pressure: 1148.43751148.4375 N/m for the design, drag 10−610^{-6}. For the flat plate the same sum gives 1141.161141.16 N/m and a spurious drag of 9191 N/m, because a sharp leading edge concentrates infinite suction at one point (leading-edge suction), which no finite sum catches; a round nose spreads it out. At 2.0979∘2.0979^\circ the sim also prints the approximations: 2π(1+ε)sin⁡(α+β)=0.50382\pi(1 + \varepsilon)\sin(\alpha + \beta) = 0.5038, while dropping the thickness factor, 2π(α+β)=0.45842\pi(\alpha + \beta) = 0.4584, is 8%8\% low.

The pressure on the skin

Bernoulli (irrotational, so between any two points) gives Cp=1−(V/U)2C_p = 1 - (V/U)^2, with VV the surface speed from the map. Plotted as −Cp-C_p (suction up), the upper surface lies above the lower; the area between them is the force coefficient normal to the chord, essentially CLC_L at small angles. The lab’s sweep for the design:

α\alphaCLC_Lpeak suction CpC_pat x/cx/c
0∘0^\circ0.24920.2492−0.599-0.5990.1470.147
4∘4^\circ0.72680.7268−1.505-1.5050.0180.018
8∘8^\circ1.20081.2008−3.885-3.8850.00390.0039
12∘12^\circ1.66891.6689−7.863-7.8630.00150.0015
15∘15^\circ2.01482.0148−11.846-11.8460.00090.0009

CLC_L grows steadily, but the suction peak grows much faster and moves onto the nose. Why: the stagnation point slides under the nose as α\alpha rises, and the air from it must race round the tight leading-edge curve to the upper surface. Behind the peak the air has to slow down again, pressure climbing back to near free-stream at the trailing edge. At 15∘15^\circ the sim’s trailing-edge speed is 43.4343.43 m/s, so Cp=1−0.86862=0.25C_p = 1 - 0.8686^2 = 0.25 there: the upper surface climbs from −11.8-11.8 to +0.25+0.25 within 1.51.5 m. That climb is the adverse pressure gradient of 11.8 Boundary Layers.

Ideal and real lift curves: stall

Potential flow’s CLC_L keeps climbing along a sine, 2.01482.0148 at 15∘15^\circ. Real wings do not, and the reason is the table above read through 11.8: the upper boundary layer must climb that pressure hill with air already slowed by no-slip. A laminar layer tolerates very little adverse gradient (Falkner–Skan), a turbulent one more (11.9), but past some angle it too stops, reverses and separates. Once the flow leaves the surface before the trailing edge, the Kutta condition no longer holds, the circulation falls, lift drops and drag jumps: stall. For typical sections at a few million Reynolds number, CL,max⁡C_{L,\max} is around 1.41.4 to 1.61.6, reached near 15∘15^\circ (from memory); the sim shades that region, an indication, not a computation.

Below stall, viscosity still nibbles: the layer thickens toward the trailing edge, so the air “sees” a slightly less cambered shape, and measured slopes are about 0.90.9 to 1.01.0 times 2π2\pi (from memory), below the Joukowski 1.09×2π1.09\times2\pi. Thickness raises the slope, viscosity lowers it, and 2πα2\pi\alpha survives as a rule of thumb.

Computing it

🐍 PythonLab: Joukowski airfoils at C_L = 0.5 (flat plate and cambered), the pressure sum, and the suction peak against alpha
⌘/Ctrl + Enter
🧪 Coding exerciseExercise: Kutta circulation, lift from circulation, and the 2 pi slope on a Joukowski airfoil
⌘/Ctrl + Enter

Graded: the flat plate’s 18.7518.75 m2^2/s, the Kutta zero, the cambered airfoil’s CL=0.5C_L = 0.5 at 2.0979∘2.0979^\circ, and the slopes 1.0000001.000000 and 1.0908971.090897 times 2π2\pi (tolerances 10−610^{-6} to 10−410^{-4}).

Concept checks

✅ Concept check

The design airfoil ($a = 0.409357$ m, $\beta = 2.0826^\circ$) flies at $U = 50$ m/s and $\alpha = 4^\circ$. What circulation, in m$^2$/s, does the Kutta condition demand?

✅ Concept check

Why does a real airfoil pick the Kutta circulation out of the infinitely many that potential flow allows?

✅ Concept check

A flat plate at $\alpha = 6^\circ$. What is its ideal $C_L$?

✅ Concept check

Potential flow predicts $C_L = 2.0148$ for the design at $15^\circ$. Why does a real wing stall near there instead?

Problems

✏️ Pen & paperThe symmetric Joukowski slope●●○

For the symmetric airfoil (κ=0\kappa = 0), show that the ideal lift slope is 4(1+ε)2+(1+2ε)+1/(1+2ε)×2π\dfrac{4(1 + \varepsilon)}{2 + (1 + 2\varepsilon) + 1/(1 + 2\varepsilon)}\times2\pi and evaluate it for ε=0.10\varepsilon = 0.10.

Show worked solution

CL=8πasin⁡α/cC_L = 8\pi a\sin\alpha/c with a=b(1+ε)a = b(1 + \varepsilon), so dCL/dα=8πb(1+ε)/cdC_L/d\alpha = 8\pi b(1 + \varepsilon)/c at α=0\alpha = 0. The chord runs from xLE=−b(1+2ε)−b/(1+2ε)x_{\text{LE}} = -b(1 + 2\varepsilon) - b/(1 + 2\varepsilon) to 2b2b. Dividing by 2π2\pi gives the formula. With ε=0.10\varepsilon = 0.10: 4.4/(2+1.2+0.8333)=4.4/4.0333=1.09094.4/(2 + 1.2 + 0.8333) = 4.4/4.0333 = 1.0909, as the sim and the exercise find.

✏️ Pen & paperA circular-arc airfoil's zero-lift angle●●○

Take ε=0\varepsilon = 0: centre ibκib\kappa, radius a=b1+κ2a = b\sqrt{1 + \kappa^2}. (a) Show the image is an arc from −2b-2b to 2b2b with height 2κb2\kappa b. (b) Find CL(α)C_L(\alpha) and αL0\alpha_{L0} for 2%2\% camber.

Show worked solution

(a) ζ=±b\zeta = \pm b are on the circle (distance b1+κ2b\sqrt{1 + \kappa^2} from the centre), mapping to z=±2bz = \pm2b. The top point is ζ=ib(κ+s)\zeta = ib(\kappa + s) with s=1+κ2s = \sqrt{1 + \kappa^2}; since (κ+s)(s−κ)=1(\kappa + s)(s - \kappa) = 1, b2/ζ=−ib(s−κ)b^2/\zeta = -ib(s - \kappa) and z=2iκbz = 2i\kappa b. So c=4bc = 4b and h/c=κ/2h/c = \kappa/2.

(b) β=arctan⁡κ\beta = \arctan\kappa, so CL=8πa4bsin⁡(α+β)=2π1+κ2sin⁡(α+β)C_L = \frac{8\pi a}{4b}\sin(\alpha + \beta) = 2\pi\sqrt{1 + \kappa^2}\sin(\alpha + \beta). For h/c=0.02h/c = 0.02, κ=0.04\kappa = 0.04: αL0=−arctan⁡0.04=−2.2906∘\alpha_{L0} = -\arctan0.04 = -2.2906^\circ, close to −2h/c=−0.04-2h/c = -0.04 rad =−2.29∘= -2.29^\circ. (In the sim: thickness 00, camber 0.040.04.)

✏️ Pen & paperHow fast round the corner?●●●

Without the Kutta condition the circle-plane velocity at ζ=b\zeta = b is some K≠0K \ne 0. Show that the airfoil speed a distance dd from the cusp is about ∣K∣b/(2d)|K|\sqrt{b}/(2\sqrt d), and check it against the sim’s 47684768 m/s at d=4.51×10−7d = 4.51\times10^{-7} m (design, α=4∘\alpha = 4^\circ, Γ=0\Gamma = 0, where ∣K∣=10.60|K| = 10.60 m/s).

Show worked solution

Put ζ=b+s\zeta = b + s. Then dz/dζ=1−b2/ζ2≈2s/bdz/d\zeta = 1 - b^2/\zeta^2 \approx 2s/b and z−2b=s2/ζ≈s2/bz - 2b = s^2/\zeta \approx s^2/b, so ∣s∣≈bd|s| \approx \sqrt{bd}. The speed is ∣K∣/∣dz/dζ∣≈∣K∣b/(2bd)=∣K∣b/(2d)|K|/|dz/d\zeta| \approx |K|b/(2\sqrt{bd}) = |K|\sqrt b/(2\sqrt d). With b=0.371897b = 0.371897 m: 10.60⋅0.6098/(2⋅6.716×10−4)=4.81×10310.60\cdot0.6098/(2\cdot6.716\times10^{-4}) = 4.81\times10^3 m/s, within 1%1\% of the sim’s 47684768 (the approximations drop higher powers of ss). It is unbounded as d→0d \to 0.

Key Takeaways

  • A conformal map only scales and rotates locally: it carries flows to flows and walls to walls, keeping the free stream and the circulation. Solve the circle, then map it.
  • Joukowski, z=ζ+b2/ζz = \zeta + b^2/\zeta, maps a circle through ζ=b\zeta = b to an airfoil: centre left for thickness, up for camber; z−2b=(ζ−b)2/ζz - 2b = (\zeta - b)^2/\zeta doubles the tail’s angle into a cusp.
  • Every Γ\Gamma but one sends the air round the cusp at unbounded speed; viscosity sheds the starting vortex until the flow leaves smoothly: Kutta, Γ=4πUasin⁡(α+β)\Gamma = 4\pi Ua\sin(\alpha + \beta).
  • L′=ρUΓL' = \rho U\Gamma and CL=8πasin⁡(α+β)/c≈2π(1+ε)sin⁡(α+β)C_L = 8\pi a\sin(\alpha + \beta)/c \approx 2\pi(1 + \varepsilon)\sin(\alpha + \beta); the flat plate’s 2πsin⁡α≈2πα2\pi\sin\alpha \approx 2\pi\alpha; the zero-lift angle is −β-\beta. Slopes: 1.0000×2π1.0000\times2\pi (plate), 1.0909×2π1.0909\times2\pi (ε=0.10\varepsilon = 0.10).
  • The light aircraft: CL=0.5C_L = 0.5 at 2.0979∘2.0979^\circ (cambered) instead of 4.5643∘4.5643^\circ (plate); Γ=18.75\Gamma = 18.75 m2^2/s either way, 1148.43751148.4375 N/m, 12 63312\,633 N over 1111 m.
  • Cp=1−(V/U)2C_p = 1 - (V/U)^2: the leading-edge suction peak deepens from −1.5-1.5 at 4∘4^\circ to −11.8-11.8 at 15∘15^\circ; the climb behind it separates the boundary layer and stalls real wings near 15∘15^\circ (from memory), while the ideal line keeps rising.
  • Next, 12.2: a general airfoil, with a finite trailing-edge angle and any shape you like, has no neat map to a circle. So we stop mapping and replace the airfoil by a sheet of vortices on its surface, demand that the surface be a streamline at every panel plus Kutta at the trailing edge, and solve the resulting linear system, your numerical-methods home turf, recovering thin airfoil theory’s 2πα2\pi\alpha and the camber’s zero-lift angle along the way.
Finished this lesson?

Mark it complete to track your progress (saved in this browser). Reading every section does this for you.

Where this leads

These later lessons build directly on this one: